ESP32-WROVER-KIT a kamera setup failed VYRIEŠENÉ

[tiimsvk]

Ahojte prišiel mi modul s kamerov typ:
ESP32-WROVER-E s osadeným headerom pre kameru.
Ale mam tu problém a nie len pri tejto doske ale aj pri klasickej esp32cam. Stále hlasi chybu kamery:

Kód: Vybrat vše

[20:25:04][E][sccb.c:115] SCCB_Write(): SCCB_Write Failed addr:0x30, reg:0x3e, data:0x00, ret:263
[20:25:04][E][sccb.c:115] SCCB_Write(): SCCB_Write Failed addr:0x30, reg:0xff, data:0x00, ret:263
[20:25:04][E][sccb.c:115] SCCB_Write(): SCCB_Write Failed addr:0x30, reg:0x05, data:0x01, ret:263
[20:25:04][E][camera.c:1344] camera_init(): Failed to set frame size
[20:25:04][E][camera.c:1406] esp_camera_init(): Camera init failed with error 0x20002
[20:25:04][E][esp32_camera:024]: esp_camera_init failed: ERROR
[20:25:04][E][component:113]: Component esp32_camera was marked as failed.


[20:25:08][C][logger:295]:   Log Baud Rate: 115200
[20:25:08][C][logger:296]:   Hardware UART: UART0
[20:25:08][C][esp32_camera:048]: ESP32 Camera:
[20:25:08][C][esp32_camera:049]:   Name: My Camera
[20:25:08][C][esp32_camera:050]:   Internal: NO
[20:25:08][C][esp32_camera:052]:   Data Pins: D0:4 D1:5 D2:18 D3:19 D4:36 D5:39 D6:34 D7:35
[20:25:08][C][esp32_camera:053]:   VSYNC Pin: 25
[20:25:08][C][esp32_camera:054]:   HREF Pin: 23
[20:25:08][C][esp32_camera:055]:   Pixel Clock Pin: 22
[20:25:08][C][esp32_camera:056]:   External Clock: Pin:21 Frequency:10000000
[20:25:08][C][esp32_camera:057]:   I2C Pins: SDA:26 SCL:27
[20:25:08][C][esp32_camera:058]:   Reset Pin: -1
[20:25:08][C][esp32_camera:076]:   Resolution: 640x480 (VGA)
[20:25:08][E][esp32_camera:095]:   Setup Failed: ERROR
[20:25:08][C][psram:020]: PSRAM:
[20:25:08][C][psram:021]:   Available: YES

Neviete kde môže byť problém mám doma 7 modulov kamier

Yaml:

Kód: Vybrat vše

#-------------------------------------------
# SUBTITUTIONS
# basic definitions and description of the device
#-------------------------------------------
substitutions:
  device_name: dev_board8266
  friendly_name: dev_board8266
  created_by: StudioTiiM 2022 
  device_description: "development board esp8266"
 
#-------------------------------------------
# Define pins

#-------------------------------------------

#-------------------------------------------
# ESP MAIN SETTINGS
#-------------------------------------------
esphome:
  name: dev-board32

esp32:
  board: esp-wrover-kit
#  framework:
#    type: arduino

logger:

api:
ota:
  password: !secret ota_pass

wifi:
  ssid: !secret wifi_ssid
  password: !secret wifi_password

  ap:
    ssid: "$friendly_name Hotspot"
    password: !secret api_pass

captive_portal:

sensor:
  
binary_sensor:

# Example configuration entry
esp32_camera:
  external_clock:
    pin: GPIO21
    frequency: 10MHz
  i2c_pins:
    sda: GPIO26
    scl: GPIO27
  data_pins: [GPIO4, GPIO5, GPIO18, GPIO19, GPIO36, GPIO39, GPIO34, GPIO35]
  vsync_pin: GPIO25
  href_pin: GPIO23
  pixel_clock_pin: GPIO22

  resolution: VGA
  jpeg_quality: 15
  idle_framerate: 0.01fps
  name: My Camera

Nejaké nápady.
Rozmyslam co uz robim zle lebo z dosiek s osadenými kamerami mi tak funguje jedna z troch.


Problém so zle napájkovanými regulátromy pre kameru je potrebné ich vymeniť viď príspevok : https://community.home-assistant.io/t/e ... ?u=tiimsvk

[Rudo1111]

Ahoj problem je v aktualizacii ESPHome bud sprvis downgrade ESPHome alebo pockas na opravu v aktualizacii.
https://github.com/esphome/issues/issues/3908

[tiimsvk]

Super dik tak skusim downgrade ked bude čas mozo to dovtedy opravia

[tiimsvk]

Takže chlapci a dievčata. Pre mňa nepochopiteľné!
Ako môže byť z vyroby zle osadený regulator na doske... tí činania asi nerobia konečnu kontrolu pred odovzdaním:

Viď príspevok na homeassistant fore:
https://community.home-assistant.io/t/e ... ?u=tiimsvk

nevadi problém vyriešený!

[Pete30]

Jo Čina je země neomezených možností